Welcome To b2b168.com, Join Free | Sign In
中文(简体) |
中文(繁體) |
Francés |Español |Deutsch |Pусский |
| No.8666722
- Product Categories
- Friendly Links
- home > Supply > Shaanxi supply hand-carried winch Hand winch manufacturers offer a mechanical winch line Bazhou
Information Name: | Shaanxi supply hand-carried winch Hand winch manufacturers offer a mechanical winch line Bazhou |
Published: | 2012-01-11 |
Validity: | 90 |
Specifications: | Complete |
Quantity: | 9999.00 |
Price Description: | |
Detailed Product Description: | Hebei motor gasoline motor winch winch winch motor gasoline mill a twist, product name: mobile winch II Model: 3T, 5T, 8T three purposes: machine Moving air twist mill is set up high-voltage transmission lines and laying of underground cable construction tools, in Complex conditions, smooth, easy to set up leather towers, set up guide (land) lines, and lifting Traction. The practical effect of experimental and field evidence, with reasonable structure, small size, light weight , Power, operating flexibility, easy handling, etc., well received by the electricity operator's welcome! Fourth, the specification: output is transferred: the slowest speed 12 rev / min, maximum speed 22 rev / min output Reverse: 11 rev / min, 20 rev / min five, structure and working principle 1, the power 3T diesel power : 4 hp Speed: 2600 r / min 5T diesel power: 8 hp Speed: 2600 r / min 2 , Transmission mode and speed: power and gear box 3T, A V-belt type two, 5T two Root B-type V-belt drive, and equipped with drive clutch. 3, the brake with automatic brake and folders from Two braking combined transmission chain brake device, the positive and negative directions are from the braking effect. 4, hand Devices: twist mill at work during the original case of engine failure, was not hanging objects No less than on the case, can toggle hand devices, will continue to be lifted or suspended material back into the ground. 5, gear box lubrication method seepage run outside of the bearing parts with butter. (1) pre-boot , You must first open the cutter mill drive clutch and the gearshift lever before and after the call to the neutral position, then Before boot. (2) Slide the clutch, the action should be fast, otherwise the chain brake does not work With the formation of automatic brake pawl of the impact. At boot time should not be too hard to belt Wheel to drive the input shaft rotation can not slip. (3) change file must be open transmission clutch , Otherwise it will damage the gear, change gear change should be checked after the file is in prison together, to prevent gear jump phenomenon. (4) block the process of change, if the income is difficult to stop the phenomenon can not be forced into the block, can hand Shake device to help block into the specific practices: hand device struck with a wrench to rotate an angle, that is Can get into gear. 5, the installation of wire rope: (1) to open the clutch drum, the rope head To wear around the roll to tighten, you can close the clutch. (2) outside the measured roll end bearing support Support activities, open seat, the rope tightened around into the reel. (3) wire rope around the law: from the bottom up Wear, that is, into the next rope, face rolls, counter-clockwise around, into the driving force behind the rope by-side, around 5 --- 6 Volume, 5T around 8 volumes, if the brakes do not work around the anti-. |
Admin>>>
You are the 11154 visitor
Copyright © GuangDong ICP No. 10089450, Bazhou Line Tool Factory All rights reserved.
Technical support: ShenZhen AllWays Technology Development Co., Ltd.
AllSources Network's Disclaimer: The legitimacy of the enterprise information does not undertake any guarantee responsibility
You are the 11154 visitor
Copyright © GuangDong ICP No. 10089450, Bazhou Line Tool Factory All rights reserved.
Technical support: ShenZhen AllWays Technology Development Co., Ltd.
AllSources Network's Disclaimer: The legitimacy of the enterprise information does not undertake any guarantee responsibility